View ADG1607BRUZ-REEL7_4515863.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

4.5 RON, 16-Channel, Differential 8-Channel, 5 V,+12 V,+5 V, and +3.3 V Multiplexers
ADG1606/ADG1607
FEATURES
4.5 typical on resistance 1.1 on resistance flatness 3.3 V to 8 V dual supply operation 3.3 V to 16 V single supply operation No VL supply required 3 V logic-compatible inputs Rail-to-rail operation Up to 378 mA of continuous current per channel 28-lead TSSOP and 32-lead, 5 mm x 5 mm LFCSP_VQ
FUNCTIONAL BLOCK DIAGRAMS
ADG1606
S1
D
S16 1-OF-16 DECODER
08489-001
A0 A1 A2 A3 EN
APPLICATIONS
Communication systems Medical systems Audio signal routing Video signal routing Automatic test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Relay replacements
Figure 1.
ADG1607
S1A DA S8A S1B DB S8B 1-OF-8 DECODER
08489-002
A0 A1 A2 EN
Figure 2.
GENERAL DESCRIPTION
The ADG1606 and ADG1607 are monolithic iCMOS(R) analog multiplexers comprising of 16 single channels and eight differential channels, respectively. The ADG1606 switches one of 16 inputs to a common output, as determined by the 4-bit binary address lines (A0, A1, A2, and A3). The ADG1607 switches one of eight differential inputs to a common differential output, as determined by the 3-bit binary address lines (A0, A1, and A2). An EN input on both devices enables or disables the device. When disabled, all channels switch off. When enabled, each channel conducts equally well in both directions and has an input signal range that extends to the supplies. The ultralow on resistance and on-resistance flatness of these switches make them ideal solutions for data acquisition and gain switching applications where low distortion is critical. iCMOS(R) construction ensures ultralow power dissipation, making the parts ideally suited for portable and batterypowered instruments.
PRODUCT HIGHLIGHTS
1. 2. 3. 4. 7.5 maximum on resistance over temperature. Minimum distortion: THD + N = 0.04% 3 V logic-compatible digital inputs: VINH = 2.0 V, VINL = 0.8 V. No VL logic power supply required.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2009 Analog Devices, Inc. All rights reserved.
ADG1606/ADG1607 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications ....................................................................................... 1 Functional Block Diagrams ............................................................. 1 General Description ......................................................................... 1 Product Highlights ........................................................................... 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 5 V Dual Supply ......................................................................... 3 12 V Single Supply ........................................................................ 4 5 V Single Supply .......................................................................... 5 3.3 V Single Supply ....................................................................... 6 Continuous Current per Channel, S or D ..................................7 Absolute Maximum Ratings ............................................................8 Thermal Resistance .......................................................................8 ESD Caution...................................................................................8 Pin Configurations and Function Descriptions ............................9 Typical Performance Characteristics ........................................... 13 Test Circuits ..................................................................................... 17 Terminology .................................................................................... 20 Outline Dimensions ....................................................................... 21 Ordering Guide .......................................................................... 21
REVISION HISTORY
10/09--Revision 0: Initial Version
Rev. 0 | Page 2 of 24
ADG1606/ADG1607 SPECIFICATIONS
5 V DUAL SUPPLY
VDD = +5 V 10%, VSS = -5 V 10%, GND = 0 V, unless otherwise noted. Table 1.
Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On Resistance Match Between Channels (RON) On Resistance Flatness (RFLAT(ON)) LEAKAGE CURRENTS Source Off Leakage, IS (Off) Drain Off Leakage, ID (Off) ADG1606 Channel On Leakage, ID, IS (On) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS 1 Transition Time, tTRANSITION tON (EN) tOFF (EN) Break-Before-Make Time Delay, tBBM Charge Injection Off Isolation Channel-to-Channel Crosstalk Total Harmonic Distortion + Noise (THD + N) -3 dB Bandwidth ADG1606 ADG1607 CS (Off) CD (Off) ADG1606 ADG1607 CD, CS (On) ADG1606 ADG1607 POWER REQUIREMENTS IDD VDD/VSS
1
25C
-40C to +85C
-40C to +125C VDD to VSS
Unit V typ max typ max typ max nA typ
Test Conditions/Comments
4.5 5.5 0.2 0.5 1.1 1.4 0.02 0.15 0.05 0.2 0.1 0.3
6.7 0.8 1.7
7.5 0.9 2
VS = 4.5 V, IS = -10 mA; see Figure 26 VDD = 4.5 V, VSS = 4.5 V VS = 4.5 V, IS = -10 mA VS = 4.5 V, IS = -10 mA VDD = +5.5 V, VSS = -5.5 V VS = 4.5 V, VD = 4.5 V; see Figure 27 VS = 4.5 V, VD = 4.5 V; see Figure 27 VS = VD = 4.5 V; see Figure 28
0.5 3 3
3 25 25 2.0 0.8
nA max nA typ nA max nA typ nA max V min V max A typ A max pF typ ns typ ns max ns typ ns max ns typ ns max ns typ ns min pC typ dB typ dB typ % typ MHz typ MHz typ pF typ pF typ pF typ pF typ pF typ A typ A max V min/max
0.003 0.1 4 175 214 132 162 124 153 42 27 -62 -62 0.04 21 37 18 248 123 271 146 0.001 1.0 3.3/8
VIN = VGND or VDD
247 180 176
275 188 202 15
RL = 300 , CL = 35 pF VS = 2.5 V; see Figure 29 RL = 300 , CL = 35 pF VS = 2.5 V; see Figure 31 RL = 300 , CL = 35 pF VS = 2.5 V; see Figure 31 RL = 300 , CL = 35 pF VS1 = VS2 = 2.5 V; see Figure 30 VS = 0 V, RS = 0 , CL = 1 nF; see Figure 32 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 33 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 35 RL = 110 , 5 V p-p, f = 20 Hz to 20 kHz; see Figure 36 RL = 50 , CL = 5 pF; see Figure 34
VS = 0 V, f = 1 MHz VS = 0 V, f = 1 MHz VS = 0 V, f = 1 MHz VS = 0 V, f = 1 MHz VS = 0 V, f = 1 MHz VDD = +5.5 V, VSS = -5.5 V Digital inputs = 0 V or VDD
Guaranteed by design, not subject to production test.
Rev. 0 | Page 3 of 24
ADG1606/ADG1607
12 V SINGLE SUPPLY
VDD = 12 V 10%, VSS = 0 V, GND = 0 V, unless otherwise noted. Table 2.
Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On Resistance Match Between Channels (RON) On Resistance Flatness (RFLAT(ON)) LEAKAGE CURRENTS Source Off Leakage, IS (Off) Drain Off Leakage, ID (Off) ADG1606 Channel On Leakage, ID, IS (On) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS1 Transition Time, tTRANSITION tON (EN) tOFF (EN) Break-Before-Make Time Delay, tBBM Charge Injection Off Isolation Channel-to-Channel Crosstalk Total Harmonic Distortion + Noise (THD + N) -3 dB Bandwidth ADG1606 ADG1607 CS (Off) CD (Off) ADG1606 ADG1607 CD, CS (On) ADG1606 ADG1607 POWER REQUIREMENTS IDD ADG1606 ADG1607 VDD
1
25C
-40C to +85C
-40C to +125C 0 V to VDD
Unit V typ max typ max typ max nA typ nA max nA typ nA max nA typ nA max V min V max A typ A max pF typ ns typ ns max ns typ ns max ns typ ns max ns typ ns min pC typ dB typ dB typ % typ MHz typ MHz typ pF typ pF typ pF typ pF typ pF typ A typ A max A typ A max A typ A max V min/max
Test Conditions/Comments
4 5 0.2 0.5 1 1.3 0.02 0.15 0.05 0.2 0.1 0.3
6.2 0.8 1.6
7 0.9 1.9
VS = 0 V to 10 V, IS = -10 mA; see Figure 26 VDD = 10.8 V, VSS = 0 V VS = 10 V, IS = -10 mA VS = 0 V to 10 V, IS = -10 mA VDD = 13.2 V, VSS = 0 V VS = 1 V/10 V, VD = 10 V/1 V; see Figure 27 VS = 1 V/10 V, VD = 10 V/1 V; see Figure 27 VS = VD = 1 V or 10 V; see Figure 28
0.5 3 3
3 25 25 2.0 0.8
0.003 0.1 4 143 170 108 128 90 109 40 33 -62 -62 0.04 22 38 18 240 120 263 143 0.001 1.0 300 480 370 600 3.3/16
VIN = VGND or VDD
198 136 132
221 142 150 15
RL = 300 , CL = 35 pF VS = 8 V; see Figure 29 RL = 300 , CL = 35 pF VS = 8 V; see Figure 31 RL = 300 , CL = 35 pF VS = 8 V; see Figure 31 RL = 300 , CL = 35 pF VS1 = VS2 = 8 V; see Figure 30 VS = 6 V, RS = 0 , CL = 1 nF; see Figure 32 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 33 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 35 RL = 110 , 5 V p-p, f = 20 Hz to 20 kHz; see Figure 36 RL = 50 , CL = 5 pF; see Figure 34
VS = 6 V, f = 1 MHz VS = 6 V, f = 1 MHz VS = 6 V, f = 1 MHz VS = 6 V, f = 1 MHz VS = 6 V, f = 1 MHz VDD = 12 V Digital inputs = 0 V or VDD Digital inputs = 5 V Digital inputs = 5 V
Guaranteed by design, not subject to production test. Rev. 0 | Page 4 of 24
ADG1606/ADG1607
5 V SINGLE SUPPLY
VDD = 5 V 10%, VSS = 0 V, GND = 0 V, unless otherwise noted. Table 3.
Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On Resistance Match Between Channels (RON) On Resistance Flatness (RFLAT(ON)) LEAKAGE CURRENTS Source Off Leakage, IS (Off) Drain Off Leakage, ID (Off) ADG1606 Channel On Leakage, ID, IS (On) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS1 Transition Time, tTRANSITION tON (EN) tOFF (EN) Break-Before-Make Time Delay, tBBM Charge Injection Off Isolation Channel-to-Channel Crosstalk Total Harmonic Distortion + Noise (THD + N) -3 dB Bandwidth ADG1606 ADG1607 CS (Off) CD (Off) ADG1606 ADG1607 CD, CS (On) ADG1606 ADG1607 POWER REQUIREMENTS IDD VDD
1
25C
-40C to +85C
-40C to +125C 0 V to VDD
Unit V typ max typ max typ max nA typ nA max nA typ nA max nA typ nA max V min V max A typ A max pF typ ns typ ns max ns typ ns max ns typ ns max ns typ ns min pC typ dB typ dB typ % typ
Test Conditions/Comments
8.5 9.5 0.3 0.8 1.8 2.4 0.01 0.15 0.02 0.2 0.05 0.3
11.5 1.1 2.7
12.5 1.2 3
VS = 0 V to 4.5 V, IS = -10 mA; see Figure 26 VDD = 4.5 V, VSS = 0 V VS = 0 V to 4.5 V, IS = -10 mA VS = 0 V to 4.5 V, IS = -10 mA VDD = 5.5 V, VSS = 0 V VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 27 VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 27 VS = VD = 1 V or 4.5 V; see Figure 28
0.5 3 3
3 25 25 2.0 0.8
0.003 0.1 4 220 280 160 202 154 197 45 12 -62 -62 0.35
VIN = VGND or VDD
324 221 232
360 234 259 15
RL = 300 , CL = 35 pF VS = 2.5 V; see Figure 29 RL = 300 , CL = 35 pF VS = 2.5 V; see Figure 31 RL = 300 , CL = 35 pF VS = 2.5 V; see Figure 31 RL = 300 , CL = 35 pF VS1 = VS2 = 2.5 V; see Figure 30 VS = 2.5 V, RS = 0 , CL = 1 nF; see Figure 32 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 33 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 35 RL = 110 , f = 20 Hz to 20 kHz, VS = 3.5 V p-p; see Figure 36 RL = 50 , CL = 5 pF; see Figure 34
19 34 20 270 137 300 160 0.001 1.0 3.3/16
MHz typ MHz typ pF typ pF typ pF typ pF typ pF typ A typ A max V min/max
VS = 2.5 V, f = 1 MHz VS = 2.5 V, f = 1 MHz VS = 2.5 V, f = 1 MHz VS = 2.5 V, f = 1 MHz VS = 2.5 V, f = 1 MHz VDD = 5.5 V Digital inputs = 0 V or VDD
Guaranteed by design, not subject to production test.
Rev. 0 | Page 5 of 24
ADG1606/ADG1607
3.3 V SINGLE SUPPLY
VDD = 3.3 V, VSS = 0 V, GND = 0 V, unless otherwise noted. Table 4.
Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On Resistance Match Between Channels (RON) On Resistance Flatness (RFLAT(ON)) LEAKAGE CURRENTS Source Off Leakage, IS (Off) Drain Off Leakage, ID (Off) ADG1606 Channel On Leakage, ID, IS (On) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS 1 Transition Time, tTRANSITION tON (EN) tOFF (EN) Break-Before-Make Time Delay, tBBM Charge Injection Off Isolation Channel-to-Channel Crosstalk Total Harmonic Distortion + Noise (THD + N) -3 dB Bandwidth ADG1606 ADG1607 CS (Off) CD (Off) ADG1606 ADG1607 CD, CS (On) ADG1606 ADG1607 POWER REQUIREMENTS IDD VDD
1
25C
-40C to +85C
-40C to +125C 0 V to VDD 15.5 0.8 6
Unit V typ typ typ nA typ nA max nA typ nA max nA typ nA max V min V max A typ A max pF typ ns typ ns max ns typ ns max ns typ ns max ns typ ns min pC typ dB typ dB typ % typ
Test Conditions/Comments
14 0.6 5 0.01 0.15 0.02 0.2 0.05 0.3
14.5 0.7 5.5
VS = 0 V to VDD, IS = -10 mA; see Figure 26 VDD = 3.3 V, VSS = 0 V VS = 0 V to VDD, IS = -10 mA VS = 0 V to VDD, IS = -10 mA VDD = 3.6 V, VSS = 0 V VS = 0.6 V/3 V, VD = 3 V/0.6 V; see Figure 27 VS = 0.6 V/3 V, VD = 3 V/0.6 V; see Figure 27 VS = VD = 0.6 V or 3 V; see Figure 28
0.5 3 3
3 25 25 2.0 0.8
0.003 0.1 4 353 482 263 362 262 348 74 6 -62 -62 0.6
VIN = VGND or VDD
536 385 391
575 396 424 15
RL = 300 , CL = 35 pF VS = 1.5 V; see Figure 29 RL = 300 , CL = 35 pF VS = 1.5 V; see Figure 31 RL = 300 , CL = 35 pF VS = 1.5 V; see Figure 31 RL = 300 , CL = 35 pF VS1 = VS2 = 1.5 V; see Figure 30 VS = 1.5 V, RS = 0 , CL = 1 nF; see Figure 32 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 33 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 35 RL = 110 , f = 20 Hz to 20 kHz, VS = 2 V p-p; see Figure 36 RL = 50 , CL = 5 pF; see Figure 34
17 31 22 290 145 350 168 0.001 1.0 3.3/16
MHz typ MHz typ pF typ pF typ pF typ pF typ pF typ A typ A max V min/max
VS = 1.5 V, f = 1 MHz VS = 1.5 V, f = 1 MHz VS = 1.5 V, f = 1 MHz VS = 1.5 V, f = 1 MHz VS = 1.5 V, f = 1 MHz VDD = 3.6 V Digital inputs = 0 V or VDD
Guaranteed by design, not subject to production test.
Rev. 0 | Page 6 of 24
ADG1606/ADG1607
CONTINUOUS CURRENT PER CHANNEL, S OR D
Table 5. ADG1606
Parameter CONTINUOUS CURRENT, S OR D VDD = +5 V, VSS = -5 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) VDD = 12 V, VSS = 0 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) VDD = 5 V, VSS = 0 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) VDD = 3.3 V, VSS = 0 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) 25C 85C 125C Unit
259 357 273 378 199 276 164 227
168 217 175 224 136 178 119 154
105 122 108 122 91 108 80 98
mA maximum mA maximum mA maximum mA maximum mA maximum mA maximum mA maximum mA maximum
Table 6. ADG1607
Parameter CONTINUOUS CURRENT, S OR D VDD = +5 V, VSS = -5 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) VDD = 12 V, VSS = 0 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) VDD = 5 V, VSS = 0 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) VDD = 3.3 V, VSS = 0 V TSSOP (JA = 97.9C/W) LFCSP (JA = 46C/W) 25C 85C 125C Unit
192 266 203 280 147 206 122 168
133 175 140 178 108 140 91 119
91 108 91 108 70 94 56 84
mA maximum mA maximum mA maximum mA maximum mA maximum mA maximum mA maximum mA maximum
Rev. 0 | Page 7 of 24
ADG1606/ADG1607 ABSOLUTE MAXIMUM RATINGS
TA = 25C, unless otherwise noted. Table 7.
Parameter VDD to VSS VDD to GND VSS to GND Analog Inputs1 Digital Inputs2 Peak Current, S or D Continuous Current, S or D3 Operating Temperature Range Industrial (B Version) Storage Temperature Range Junction Temperature Reflow Soldering Peak Temperature, Pb Free
1
THERMAL RESISTANCE
JA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 8. Thermal Resistance
Package Type 28-Lead TSSOP 32-Lead LFCSP_VQ JA 97.9 46 JC 14 Unit C/W C/W
Rating 18 V -0.3 V to +18 V +0.3 V to -18 V VSS - 0.3 V to VDD + 0.3 V or 30 mA, whichever occurs first GND - 0.3 V to VDD + 0.3 V or 30 mA, whichever occurs first 1.1 A (pulsed at 1 ms, 10% duty cycle maximum) Data + 15% -40C to +125C -65C to +150C 150C 260C
ESD CAUTION
Overvoltages at IN, S, or D are clamped by internal diodes. Current should be limited to the maximum ratings given. 2 Overvoltages at the Ax, EN, Sx, or Dx pins are clamped by internal diodes. Current should be limited to the maximum ratings given. 3 See Table 5.
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Only one absolute maximum rating may be applied at any one time.
Rev. 0 | Page 8 of 24
ADG1606/ADG1607 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
NC NC S16 S15 S14 S13 S12 S11
2 3 4 5 6 7 8 9 27 26 25
VSS S8 S7 S6 S5 S4 S3 S2 S1 EN A0 A1
08489-003
ADG1606
TOP VIEW (Not to Scale)
24 23 22 21 20 19 18 17 16 15
S10 10 S9 11 GND 12 NC 13 A3 14
S16 S15 S14 S13 S12 S11 S10 S9
1 2 3 4 5 6 7 8
32 31 30 29 28 27 26 25
NC VDD NC D NC NC NC VSS
VDD 1
28
D
PIN 1 INDICATOR
ADG1606
TOP VIEW (Not to Scale)
24 23 22 21 20 19 18 17
S8 S7 S6 S5 S4 S3 S2 S1
NC = NO CONNECT
Figure 3. ADG1606 TSSOP Pin Configuration
Figure 4. ADG1606 LFCSP_VQ Pin Configuration
Table 9. ADG1606 Pin Function Descriptions
TSSOP 1 2, 3, 13 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin No. LFCSP_VQ 31 12, 13, 26, 27, 28, 30, 32 1 2 3 4 5 6 7 8 9 10 11 14 15 16 17 18 19 20 21 22 23 24 25 29 EPAD Mnemonic VDD NC S16 S15 S14 S13 S12 S11 S10 S9 GND A3 A2 A1 A0 EN S1 S2 S3 S4 S5 S6 S7 S8 VSS D Exposed Pad Description Most Positive Power Supply Potential. No Connect. Source Terminal 16. This pin can be an input or an output. Source Terminal 15. This pin can be an input or an output. Source Terminal 14. This pin can be an input or an output. Source Terminal 13. This pin can be an input or an output. Source Terminal 12. This pin can be an input or an output. Source Terminal 11. This pin can be an input or an output. Source Terminal 10. This pin can be an input or an output. Source Terminal 9. This pin can be an input or an output. Ground (0 V) Reference. Logic Control Input. Logic Control Input. Logic Control Input. Logic Control Input. Active High Digital Input. When this pin is low, the device is disabled and all switches are turned off. When this pin is high, the Ax logic inputs determine which switch is turned on. Source Terminal 1. This pin can be an input or an output. Source Terminal 2. This pin can be an input or an output. Source Terminal 3. This pin can be an input or an output. Source Terminal 4. This pin can be an input or an output. Source Terminal 5. This pin can be an input or an output. Source Terminal 6. This pin can be an input or an output. Source Terminal 7. This pin can be an input or an output. Source Terminal 8. This pin can be an input or an output. Most Negative Power Supply Potential. In single-supply applications, this pin can be connected to ground. Drain Terminal. This pin can be an input or an output. The exposed pad is connected internally. For increased reliability of the solder joints and maximum thermal capability, it is recommended that the pad be soldered to the substrate, VSS.
Rev. 0 | Page 9 of 24
08489-004
A2
NOTES 1. NC = NO CONNECT. 2. EXPOSED PAD TIED TO SUBSTRATE, VSS.
GND A3 A2 NC NC A1 A0 EN
9 10 11 12 13 14 15 16
ADG1606/ADG1607
Table 10. ADG1606 Truth Table
A3 X1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
1
A2 X1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
A1 X1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
A0 X1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
EN 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
On Switch None 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
X = don't care.
Rev. 0 | Page 10 of 24
ADG1606/ADG1607
DB NC S8B S7B S6B S5B S4B S3B
2 3 4 5 6 7 8 9 27 26 25
VSS S8A S7A S6A S5A S4A S3A S2A S1A EN A0 A1
08489-005
ADG1607
TOP VIEW (Not to Scale)
24 23 22 21 20 19 18 17 16 15
S2B 10 S1B 11 GND 12 NC 13 NC 14
S8B S7B S6B S5B S4B S3B S2B S1B
1 2 3 4 5 6 7 8
32 31 30 29 28 27 26 25
24 23 22 21 20 19 18 17
NC DB NC VDD NC DA NC VSS
VDD 1
28
DA
PIN 1 INDICATOR
ADG1607
TOP VIEW (Not to Scale)
S8A S7A S6A S5A S4A S3A S2A S1A
NC = NO CONNECT
Figure 5. ADG1607 TSSOP Pin Configuration
Figure 6. ADG1607 LFCSP_VQ Pin Configuration
Table 11. ADG1607 Pin Function Descriptions
TSSOP 1 2 3, 13, 14 4 5 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin No. LFCSP_VQ 29 31 11, 12, 13, 26, 28, 30, 32 1 2 3 4 5 6 7 8 9 10 14 15 16 17 18 19 20 21 22 23 24 25 27 EPAD Mnemonic VDD DB NC S8B S7B S6B S5B S4B S3B S2B S1B GND A2 A1 A0 EN S1A S2A S3A S4A S5A S6A S7A S8A VSS DA Exposed Pad Description Most Positive Power Supply Potential. Drain Terminal B. This pin can be an input or an output. No Connect. Source Terminal 8B. This pin can be an input or an output. Source Terminal 7B. This pin can be an input or an output. Source Terminal 6B. This pin can be an input or an output. Source Terminal 5B. This pin can be an input or an output. Source Terminal 4B. This pin can be an input or an output. Source Terminal 3B. This pin can be an input or an output. Source Terminal 2B. This pin can be an input or an output. Source Terminal 1B. This pin can be an input or an output. Ground (0 V) Reference. Logic Control Input. Logic Control Input. Logic Control Input. Active High Digital Input. When this pin is low, the device is disabled and all switches are turned off. When this pin is high, the Ax logic inputs determine which switch is turned on. Source Terminal 1A. This pin can be an input or an output. Source Terminal 2A. This pin can be an input or an output. Source Terminal 3A. This pin can be an input or an output. Source Terminal 4A. This pin can be an input or an output. Source Terminal 5A. This pin can be an input or an output. Source Terminal 6A. This pin can be an input or an output. Source Terminal 7A. This pin can be an input or an output. Source Terminal 8A. This pin can be an input or an output. Most Negative Power Supply Potential. In single-supply applications, this pin can be connected to ground. Drain Terminal A. This pin can be an input or an output. The exposed pad is connected internally. For increased reliability of the solder joints and maximum thermal capability, it is recommended that the pad be soldered to the substrate, VSS.
Rev. 0 | Page 11 of 24
08489-006
A2
NOTES 1. NC = NO CONNECT. 2. EXPOSED PAD TIED TO SUBSTRATE, VSS.
GND A2 NC NC NC A1 A0 EN
9 10 11 12 13 14 15 16
ADG1606/ADG1607
Table 12. ADG1607 Truth Table
A2 X1 0 0 0 0 1 1 1 1
1
A1 X1 0 0 1 1 0 0 1 1
A0 XX1 0 1 0 1 0 1 0 1
EN 0 1 1 1 1 1 1 1 1
On Switch Pair None 1 2 3 4 5 6 7 8
X = don't care.
Rev. 0 | Page 12 of 24
ADG1606/ADG1607 TYPICAL PERFORMANCE CHARACTERISTICS
7 TA = 25C 6 5 VDD = +3.3V VSS = -3.3V 6 7
VDD = 12V VSS = 0V
ON RESISTANCE ()
ON RESISTANCE ()
5
TA = +125C
4 3
4
TA = +85C TA = +25C TA = -40C
VDD = +5V VSS = -5V VDD = +8V VSS = -8V
3 2 1
2 1 0 -8 -6 -4 -2
0
2
4
6
8
10
12
SOURCE OR DRAIN VOLTAGE (V)
SOURCE OR DRAIN VOLTAGE (V)
Figure 7. On Resistance as a Function of VD (VS) for Dual Supply
16 14 12
ON RESISTANCE ()
Figure 10. On Resistance as a Function of VD (VS) for Different Temperatures, 12 V Single Supply
12
VDD = 3.3V VSS = 0V
TA = 25C
10
TA = +125C TA = +85C TA = +25C
ON RESISTANCE ()
10 8 6 4 2 0
0 2 4 6 8 10 12 14 16
08489-008
8
VDD = 5V VSS = 0V
6
TA = -40C
VDD = 12V VSS = 0V
VDD = 16V VSS = 0V
4
2
VDD = 5V VSS = 0V
0
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 SOURCE OR DRAIN VOLTAGE (V)
08489-011
08489-012
SOURCE OR DRAIN VOLTAGE (V)
Figure 8. On Resistance as a Function of VD (VS) for Single Supply
7
VDD = +5V VSS = -5V
Figure 11. On Resistance as a Function of VD (VS) for Different Temperatures, 5 V Single Supply
18 16 14 VDD = 3.3V VSS = 0V
6 5
TA = +125C TA = +85C
ON RESISTANCE ()
ON RESISTANCE ()
12 10 8 6 4
4
TA = +25C
TA = +125C TA = +85C TA = +25C TA = -40C
3
TA = -40C
2 1 0 -5
2 0
08489-009
-4
-3
-2
-1
0
1
2
3
4
5
0
0.5
1.0
1.5
2.0
2.5
3.0
SOURCE OR DRAIN VOLTAGE (V)
SOURCE OR DRAIN VOLTAGE (V)
Figure 9. On Resistance as a Function of VD (VS) for Different Temperatures, 5 V Dual Supply
Figure 12. On Resistance as a Function of VD (VS) for Different Temperatures, 3.3 V Single Supply
Rev. 0 | Page 13 of 24
08489-010
0
2
4
6
8
08489-007
0
ADG1606/ADG1607
25 20 15
LEAKAGE CURRENT (nA)
12 VDD = +5V VSS = -5V VBIAS = +4.5V/-4.5V ID (OFF) - + ID (ON) + + IS (OFF) + -
LEAKAGE CURRENT (nA)
10
VDD = 3.3V VSS = 0V VBIAS = 0.6V/3V
ID, IS (ON) + + ID (OFF) - +
10 5 0 -5
IS (OFF) - +
8
6 ID, IS (ON) - - 4 IS (OFF) + - ID (OFF) + - 2 IS (OFF) - +
ID (ON) - - -10 -15
08489-013
ID (OFF) + -
0
20
40
60
80
100
120 130
0
20
40
60
80
100
120 130
TEMPERATURE (C)
TEMPERATURE (C)
Figure 13. Leakage Currents as a Function of Temperature, 5 V Dual Supply
20 15
LEAKAGE CURRENT (nA)
Figure 16. Leakage Currents as a Function of Temperature, 3.3 V Single Supply
1000
VDD = 12V VSS = 0V VBIAS = 1V/10V
ID (ON) + + ID (OFF) - + IS (OFF) + - IS (OFF) - +
IDD (A)
IDD = ALL LOGIC HIGH TA = 25C 800 VDD = +12V VSS = 0V 600
10 5
0 -5
400 VDD = +5V VSS = -5V 200 VDD = +5V VSS = 0V VDD = +3.3V VSS = 0V 0 2 4 6 8 10 12 14
08489-017
ID (ON) - - ID (OFF) + -
-10
0
20
40
60
80
100
120 130
TEMPERATURE (C)
08489-014
-15
0
LOGIC LEVEL (V)
Figure 14. Leakage Currents as a Function of Temperature, 12 V Single Supply
Figure 17. IDD vs. Logic Level
30 25
LEAKAGE CURRENT (nA)
45
VDD = 5V VSS = 0V VBIAS = 1V/4.5V
TA = 25C 40
VDD = +12V VSS = 0V VDD = +5V VSS = -5V
ID, IS (ON) + + ID (OFF) - +
CHARGE INJECTION (pC)
35 30 25 20 15 10 5
20 15
ID, IS (ON) - - IS (OFF) + - IS (OFF) - +
10 5
VDD = +5V VSS = 0V
IS (OFF) + -
0
0
08489-015
-5 0 20 40 60 80 100 120 130 TEMPERATURE (C)
-5 -6
-4
-2
0
2
4
6
8
10
12
VS (V)
Figure 15. Leakage Currents as a Function of Temperature, 5 V Single Supply
Figure 18. Charge Injection vs. Source Voltage
Rev. 0 | Page 14 of 24
08489-018
VDD = +3.3V VSS = 0V
08489-016
-20
0
ADG1606/ADG1607
450 TA = 25C 400 VDD = +3.3V, VSS = 0V 350
ISOLATOIN (dB)
0 -10 -20 -30 -40 -50 -60 -70 -80 -90
08489-019
TA = 25C VDD = +5V VSS = -5V
300
TIME (ns)
250 200 150 100 50 0 -40
VDD = +5V, VSS = 0V
VDD = +12V, VSS = 0V
VDD = +5V, VSS = -5V
-20
0
20
40
60
80
100
120
100k
1M
10M
100M
500M
TEMPERATURE (C)
FREQUENCY (Hz)
Figure 19. Transition Time vs. Temperature
0 TA = 25C VDD = +5V VSS = -5V
Figure 21. ADG1606 Crosstalk vs. Frequency
0 TA = 25C VDD = +5V VSS = -5V ADJACENT CHANNEL
CROSSTALK (dB)
-20
OFF ISOLATOIN (dB)
-20
-40
-40
-60
-60 NONADJACENT CHANNEL -80
-80
-100
-100
08489-020
100k
1M
10M
100M
500M
100k
1M
10M
100M
500M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 20. Off Isolation vs. Frequency
Figure 22. ADG1607 Crosstalk vs. Frequency
Rev. 0 | Page 15 of 24
08489-022
-120 30k
-120 30k
08489-021
-100 30k
ADG1606/ADG1607
0 0 -10 -1
INSERTION LOSS (dB)
-20 -30
TA = 25C VDD = +5V VSS = -5V NO DECOUPLING CAPACITORS
-2
ACPSRR (dB)
-40 -50 -60 -70 -80 DECOUPLING CAPACITORS ON SUPPLIES
08489-025
-3
-4
-5
-6 30k
08489-023
TA = 25C VDD = +5V VSS = -5V 100k 1M FREQUENCY (Hz) 10M 40M
-90 -100 1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 23. ADG1606 On Response vs. Frequency
0.7 0.6 RL = 110 TA = 25C
Figure 25. ACPSRR vs. Frequency
0.5
THD + N (%)
VDD = 3.3V, VS = 2V p-p VDD = 5V, VS = 3.5V p-p
0.4
0.3
0.2 VDD = 12V, VS = 5V p-p 0.1 VDD = 5V, VSS = 5V, VS = 5V p-p
08489-024
0 0 5k 10k FREQUENCY (Hz) 15k 20k
Figure 24. THD + N vs. Frequency
Rev. 0 | Page 16 of 24
ADG1606/ADG1607 TEST CIRCUITS
V
ID (ON)
S D IDS
08489-026
NC
S
D
A VD
08489-028
VS
NC = NO CONNECT
Figure 26. On Resistance
IS (OFF) A VS S D ID (OFF) A VD
08489-027
Figure 28. On Leakage
Figure 27. Off Leakage
VDD 3V ADDRESS DRIVE (VIN) 0V 50% 50% VIN 50
VSS
tr < 20ns tf < 20ns
VDD A0 A1 A2 A3
VSS S1 S2 TO S15 S16 VS16 OUTPUT D GND 300 35pF
08489-029
VS1
tTRANSITION
tTRANSITION
90%
ADG16061
2.4V EN
OUTPUT
90%
1SIMILAR CONNECTION FOR ADG1607.
Figure 29. Address to Output Switching Times, tTRANSITION
VDD 3V VDD ADDRESS DRIVE (VIN) 0V VIN 50 A0 A1 A2 A3
VSS
VSS S1 S2 TO S15 S16 VS
80% OUTPUT
80% 2.4V
ADG16061
EN GND D
OUTPUT
300
35pF
08489-030
tBBM
1SIMILAR CONNECTION FOR ADG1607.
Figure 30. Break-Before-Make Delay, tBBM
Rev. 0 | Page 17 of 24
ADG1606/ADG1607
VDD 3V ENABLE DRIVE (VIN) 0V 50% 50% VSS
VDD A0 A1 A2 A3
VSS S1 S2 TO S16 VS
tON (EN)
0.9VOUT OUTPUT
tOFF (EN)
0.9VOUT VIN 50
ADG16061
EN GND D
OUTPUT
300
35pF
08489-031
1SIMILAR CONNECTION FOR ADG1607.
Figure 31. Enable Delay, tON (EN), tOFF (EN)
VDD
VSS
3V
VDD A0 A1 A2 A3
VSS
VIN
ADG16061
RS VOUT QINJ = CL x VOUT VOUT VS VIN GND S EN D CL 1nF VOUT
1SIMILAR CONNECTION FOR ADG1607.
Figure 32. Charge Injection
Rev. 0 | Page 18 of 24
08489-032
ADG1606/ADG1607
VDD 0.1F VSS 0.1F NETWORK ANALYZER
VDD 0.1F NETWORK ANALYZER VOUT RL 50
VSS 0.1F
VDD S
VSS
VDD S1
VSS
50 D
50 VS VOUT
D S2 VS
R 50
GND
RL 50
GND
OFF ISOLATION = 20 log
VOUT VS
08489-033
CHANNEL-TO-CHANNEL CROSSTALK = 20 log
VOUT VS
Figure 33. Off Isolation
VDD 0.1F VSS 0.1F
Figure 35. Channel-to-Channel Crosstalk
VDD
VDD S VSS NETWORK ANALYZER
VSS 0.1F AUDIO PRECISION
0.1F
50 VS D RL 50 VOUT
VDD S IN
VSS
RS VS V p-p RL 10k VOUT
D VIN
08489-034
GND
GND
INSERTION LOSS = 20 log
VOUT WITH SWITCH VOUT WITHOUT SWITCH
Figure 34. Bandwidth
Figure 36. THD + N
Rev. 0 | Page 19 of 24
08489-036
08489-035
ADG1606/ADG1607 TERMINOLOGY
RON Ohmic resistance between the D and S terminals. RON Difference between the RON of any two channels. RFLAT(ON) Flatness is defined as the difference between the maximum and minimum value of on resistance as measured. IS (Off) Source leakage current when the switch is off. ID (Off) Drain leakage current when the switch is off. ID, IS (On) Channel leakage current when the switch is on. VD, VS Analog voltage on Terminal D and Terminal S. CS (Off) Channel input capacitance for the off condition. CD (Off) Channel output capacitance for the off condition. CD, CS (On) On switch capacitance. CIN Digital input capacitance. tON (EN) Delay time between the 50% and 90% points of the digital input and the switch on condition. tOFF (EN) Delay time between the 50% and 90% points of the digital input and the switch off condition. tTRANSITION Delay time between the 50% and 90% points of the digital inputs and the switch on condition when switching from one address state to another. tBBM Off time measured between the 80% points of the switches when switching from one address state to another. VINL Maximum input voltage for Logic 0. VINH Minimum input voltage for Logic 1. IINL, IINH Input current of the digital input. IDD Positive supply current. ISS Negative supply current. Off Isolation A measure of unwanted signal coupling through an off channel. Charge Injection A measure of the glitch impulse transferred from the digital input to the analog output during switching. Bandwidth The frequency at which the output is attenuated by 3 dB. On Response The frequency response of the on switch. THD + N The ratio of the harmonic amplitude plus noise of the signal to the fundamental. AC Power Supply Rejection Ratio (ACPSRR) Measures the ability of a part to avoid coupling noise and spurious signals that appear on the supply voltage pin to the output of the switch. The dc voltage on the device is modulated by a sine wave of 0.62 V p-p. The ratio of the amplitude of signal on the output to the amplitude of the modulation is the ACPSRR.
Rev. 0 | Page 20 of 24
ADG1606/ADG1607 OUTLINE DIMENSIONS
9.80 9.70 9.60
28
15
4.50 4.40 4.30 6.40 BSC
1 14
PIN 1 0.65 BSC 0.15 0.05 COPLANARITY 0.10 0.30 0.19 1.20 MAX 8 0 0.75 0.60 0.45
SEATING PLANE
0.20 0.09
COMPLIANT TO JEDEC STANDARDS MO-153-AE
Figure 37. 28-Lead Thin Shrink Small Outline Package [TSSOP] (RU-28) Dimensions shown in millimeters
5.00 BSC SQ
0.60 MAX 0.60 MAX
25 24 32 1
PIN 1 INDICATOR
PIN 1 INDICATOR TOP VIEW 4.75 BSC SQ
0.50 BSC
EXPOSED PAD (BOTTOM VIEW)
17 16 8
3.25 3.10 SQ 2.95
0.50 0.40 0.30
9
0.25 MIN 3.50 REF
12 MAX
0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM
1.00 0.85 0.80
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 38. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 5 mm x 5 mm Body, Very Thin Quad (CP-32-2) Dimensions shown in millimeters
ORDERING GUIDE
Model ADG1606BRUZ 1 ADG1606BRUZ-REEL71 ADG1606BCPZ-REEL71 ADG1607BRUZ1 ADG1607BRUZ-REEL71 ADG1607BCPZ-REEL71
1
Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C
Package Description 28-Lead Thin Shrink Small Outline Package [TSSOP] 28-Lead Thin Shrink Small Outline Package [TSSOP] 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 28-Lead Thin Shrink Small Outline Package [TSSOP] 28-Lead Thin Shrink Small Outline Package [TSSOP] 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
011708-A
SEATING PLANE
0.30 0.23 0.18
0.20 REF
COPLANARITY 0.08
FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET.
Package Option RU-28 RU-28 CP-32-2 RU-28 RU-28 CP-32-2
Z = RoHS Compliant Part.
Rev. 0 | Page 21 of 24
ADG1606/ADG1607 NOTES
Rev. 0 | Page 22 of 24
ADG1606/ADG1607 NOTES
Rev. 0 | Page 23 of 24
ADG1606/ADG1607 NOTES
(c)2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08489-0-10/09(0)
Rev. 0 | Page 24 of 24

▲Up To Search▲

Price & Availability of ADG1607BRUZ-REEL7

	To Download ADG1607BRUZ-REEL7 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .